尊龙凯时最新平台登录

高速线缆

  2. 首页
  3. 高速线缆
  4. 40G QSFP+ 无源电缆

标准协议光� ？�

兼容协议光� ？�

其它种类光器件

手艺支持

40G QSFP+ 无源电缆

0.0/5 rating (0 votes)

Description

F-tone公司专业研发制造40G QSFP+ 无源电缆、QSFP+ Passive Copper Cable，切合MSA SFF-8436, 应用于40G以太网和InfiniBand等数据中央互联场景。。100%完善兼容全系列品牌效劳器,交流机,路由器,PDH/SDH传输装备,EPON,GPON,10G EPON,10G GPON,WDM PON基站等等全系列装备

QSFP-Cables

QSFP+ Passive Copper Cable

 

Features

  1. QSFP+ conforms to the Small Form Factor SFF-8436
  2. 4-Channel Full-Duplex Passive Copper Cable Transceiver
  3. Support for multi-gigabit data rates :1.0 Gbps - 10.3125 Gbps (per channel)
  4. Maximum aggregate data rate: 41.25 Gps (4 x 10.3125Gbit/s)
  5. Copper link length up to 5m (passive limiting)
  6. High-Density QSFP 38-PIN Connector
  7. Power Supply :+3.3V
  8. Low power consumption: 0.02 W (typ.)
  9. I2C based two-wire serial interface for EEPROM signature which can be
  10. Temperature Range: 0~ 70 °C

Applications

  1. 10G/40Gigabit Ethernet
  2. InfiniBand 4XSDR, DDR, QDR
  3. Switches, Routers, and HBAs
  4. Data Centers
  5. 2, 4, 8, 10 Gigabit Fibre Channel

STANDARDS COMPLIANCE

  1. IEEE 802.3ba
  2. SFF-8436
  3. QDR InfiniBand
  4. QSFP+ MSA
  5. RoHS Compliant

Product Description

The QSFP+ passive cable assemblies are high performance，cost effective I/O solutions for 40G LAN, HPC and SAN applications. The QSFP+ passive copper cables are compliant with SFF-8436, QSFP+ MSA and IEEE P802.3ba 40GBASE-CR4. It is offer a low power consumption，short reach intercon- nect applications. The cable each lane is capable of transmitting data at rates up to 10Gb/s, providing an aggregated rate of 40Gb/s.

Recommended Operating Conditions

Parameter

Symbol

Min

Typical

Max

Unit

Storage Ambient Temperature

  

-40

  

+85

°C

Operating Case Temperature

Tc

0

  

+70

°C

Power Supply Voltage

VCC3

3.14

3.3

3.47

V

Power Dissipation

PD

    

0.02

W


Pin Descriptions


Pin

Logic

Symbol

Name/Description

Notes

1

  

GND

Ground

1

2

CML-I

Tx2n

Transmitter Inverted Data Input

  

3

CML-I

Tx2p

Transmitter Non-Inverted Data Input

  

4

  

GND

Ground

1

5

CML-I

Tx4n

Transmitter Inverted Data Input

  

6

CML-I

Tx4p

Transmitter Non-Inverted Data Input

  

7

  

GND

Ground

1

8

LVTTL-I

ModSelL

Module Select

  

9

LVTTL-I

ResetL

Module Reset

  

10

  

Vcc Rx

+3.3V Power Supply Receiver

2

11

LVCMOSI/O

SCL

2-wire serial interface clock

  

12

LVCMOSI/O

SDA

2-wire serial interface data

  

13

  

GND

Ground

1

14

CML-O

Rx3p

Receiver Non-Inverted Data Output

  

15

CML-O

Rx3n

Receiver Inverted Data Output

  

16

  

GND

Ground

1

17

CML-O

Rx1p

Receiver Non-Inverted Data Output

  

18

CML-O

Rx1n

Receiver Inverted Data Output

  

19

  

GND

Ground

1

20

  

GND

Ground

1

21

CML-O

Rx2n

Receiver Inverted Data Output

  

22

CML-O

Rx2p

Receiver Non-Inverted Data Output

  

23

  

GND

Ground

1

24

CML-O

Rx4n

Receiver Inverted Data Output

  

25

CML-O

Rx4p

Receiver Non-Inverted Data Output

  

26

  

GND

Ground

1

27

LVTTL-O

ModPrsL

Module Present

  

28

LVTTL-O

IntL

Interrupt

  

29

  

Vcc Tx

+3.3V Power supply transmitter

2

30

  

Vcc1

+3.3V Power supply

2

31

LVTTL-I

LPMode

Low Power Mode

  

32

  

GND

Ground

1

33

CML-I

Tx3p

Transmitter Non-Inverted Data Input

  

34

CML-I

Tx3n

Transmitter Inverted Data Input

  

35

  

GND

Ground

1

36

CML-I

Tx1p

Transmitter Non-Inverted Data Input

  

37

CML-I

Tx1n

Transmitter Inverted Data Input

  

38

  

GND

Ground

1

Note 1: GND is the symbol for signal and supply (power) common for the QSFP+ module. All are common within the QSFP+ module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal-common ground plane.

Note 2: Vcc Rx, Vcc1 and Vcc Tx are the receiver and transmitter power supplies and shall be applied concurrent- ly. Requirements defined for the host side of the Host Edge Card Connector are listed in Table 6. Recommended host board power supply filtering is shown in Figure 4. Vcc Rx Vcc1 and Vcc Tx may be internally connected with- in the QSFP+ Module module in any combination. The connector pins are each rated for a maximum current of 500 mA.

Ordering information

Part Number

Product Description

QSFP-PC-01

4 x 10Gbps QSFP+ Direct Attach Cables, 1m (30AWG),0?C ~ +70?C

QSFP-PC-03

4 x 10Gbps QSFP+ Direct Attach Cables, 3m (30AWG),0?C ~ +70?C

QSFP-PC-05

4 x 10Gbps QSFP+ Direct Attach Cables, 5m (28AWG),0?C ~ +70?C

 

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone before they become applicable to any particular order or contract. In accordance with the F-tone policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone or others. Further details are available from any F-tone sales representative.

Search

网站地图